Bootlog

Below are three traces of bootlogging:

  • Terminal - RedBoot, the bootloader
  • Terminal - Linux, the kernel booting
  • Dmesg, the Linux kernel logfile

Terminal - RedBoot

RedBoot is used as the bootloader for the Newisys NA-1400. It’s task is to load the kernel (from harddisk, network or USB storage device) into memory and run it.

***###+DRAM: OK
+
***###+PIC: OK

***###+FLASH: OK
i82541er_init: RedBoot MAC Address = A0 83 00 00 48 BE
i82541er_init: read from config: ok
Can't get BOOTP info, using default IP address
Ethernet eth0: MAC address 00:09:3d:14:83:5f
IP: 127.0.0.0/255.255.255.0, Gateway: 0.0.0.0
Default server: 0.0.0.0, DNS server IP: 0.0.0.0
usb_ohci: Did not find device

***###+SATA: OK

RedBoot(tm) bootstrap and debug environment [ROM]
Intel IOP RedBoot modfied by AppianceWare for Sanmina release
         version 2.1-IOP-RedBoot-ApplianceWare-Sanmina
         built 19:07:50, Dec 14 2005

Platform: Sanmina (XScale)
Copyright (C) 2000, 2001, 2002, Red Hat, Inc.

RAM: 0x00000000-0x10000000, 0x00033168-0x0ffd1000 available
FLASH: 0xf0000000 - 0xf1000000, 128 blocks of 0x00020000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
RedBoot> fis load initrd
RedBoot> fis load kernel
RedBoot> exec -r 0x02000000 -s 0x01008000 -c "satadriver=sata_vsc fstype=xfs  console=ttyS0,115200 cachepolicy=writealloc ecc=on initrd=0xa2000000,8M"
Using base address 0x01008000 and length 0x00174d68
The boot tags are located at 0xA0000100
Booting the kernel...

Terminal - Linux

Below is a log created while capturing the first COM port on the Newisys NA-1400 during booting. It continues where the RedBoot bootloader stage ends.

Uncompressing Linux.................................................................................................... done, booting the kernel.
Linux version 2.6.10-sanmina-aw22 (sandman@alconost.sam-solutions.net) (gcc version 3.4.3 20050104 (ALT Linux, build 3.4.3-alt2)) #1 Wed Dec 14 18:10:39 MSK 2005
CPU: XScale-IOP8032x Family [69052e30] revision 0 (ARMv5TE)
CPU: D VIVT undefined 5 cache
CPU: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Machine: Sanmina
Memory policy: ECC enabled, Data cache writealloc
Built 1 zonelists
Kernel command line: satadriver=sata_vsc fstype=xfs  console=ttyS0,115200 cachepolicy=writealloc ecc=on initrd=0xa2000000,8M
PID hash table entries: 2048 (order: 11, 32768 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB = 256MB total
Memory: 248192KB available (2469K code, 595K data, 92K init)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 8192K
NET: Registered protocol family 16
machine_arch_type: 327
PCI init
maÓhine similar to iq31244
PCI: bus0: Fast back to back transfers disabled
pci_dev->irq: 0 pci_dev->pretty_name: Intel Corp. 82541EI Gigabit Ethernet Controller idsel: 1 pin: 1
pci_dev->irq: 14 pci_dev->pretty_name: Intel Corp. GD31244 PCI-X SATA HBA idsel: 3 pin: 1
pci_dev->irq: 0 pci_dev->pretty_name: Intel Corp. 82541EI Gigabit Ethernet Controller (#2) idsel: 4 pin: 1
pci_dev->irq: 0 pci_dev->pretty_name: Philips Semiconductors USB 1.1 Host Controller idsel: 5 pin: 1
pci_dev->irq: 0 pci_dev->pretty_name: Philips Semiconductors USB 1.1 Host Controller (#2) idsel: 5 pin: 1
pci_dev->irq: 0 pci_dev->pretty_name: Philips Semiconductors USB 2.0 Host Controller idsel: 5 pin: 1
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Enable CCNT succ
Intel IOP3XX DMA Copyright(c) 2004 Intel Corporation
NetWinder Floating Point Emulator V0.97 (double precision)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with ACLs, security attributes, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
I2C: M41ST85W RTC driver successfully loaded
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0xfe800000 (irq = 30) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
Intel(R) PRO/1000 Network Driver - version 5.5.4-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
netconsole: not configured, aborting
ohci_hcd 0000:00:05.0: Philips Semiconductors USB 1.1 Host Controller
ohci_hcd 0000:00:05.0: irq 30, pci mem 0x80041000
ohci_hcd 0000:00:05.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd 0000:00:05.1: Philips Semiconductors USB 1.1 Host Controller (#2)
ohci_hcd 0000:00:05.1: irq 30, pci mem 0x80042000
ohci_hcd 0000:00:05.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
I2C transfer error
I2C transfer error
Querying interrupt mode from PIC unsuccessful.  Returned 0
Defaulting to Polled Mode
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Using initd v. 0.3.0-aw29
Doing XScale specific procedures...
ata1: SATA max UDMA/133 cmd 0xD086A200 ctl 0xD086A229 bmdma 0xD086A270 irq 27
ata2: SATA max UDMA/133 cmd 0xD086A400 ctl 0xD086A429 bmdma 0xD086A470 irq 27
ata3: SATA max UDMA/133 cmd 0xD086A600 ctl 0xD086A629 bmdma 0xD086A670 irq 27
ata4: SATA max UDMA/133 cmd 0xD086A800 ctl 0xD086A829 bmdma 0xD086A870 irq 27
ata1: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48

Hotplug event!
Hotplug event on port:0
ata1: dev 0 configured for UDMA/133
scsi0 : sata_vsc
ata2: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48

Hotplug event!
Hotplug event on port:1
ata2: dev 0 configured for UDMA/133
scsi1 : sata_vsc
ata3: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48

Hotplug event!
Hotplug event on port:2
ata3: dev 0 configured for UDMA/133
scsi2 : sata_vsc
ata4: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48

Hotplug event!
Hotplug event on port:3
ata4: dev 0 configured for UDMA/133
scsi3 : sata_vsc
elevator: using anticipatory as default io scheduler
  Vendor: ATA       Model: ST3250824AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
  Vendor: ATA       Model: ST3250824AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 >
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0,  type 0
  Vendor: ATA       Model: ST3250824AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdc: drive cache: write back
 sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 >
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0,  type 0
  Vendor: ATA       Model: ST3250824AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdd: drive cache: write back
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdd: drive cache: write back
 sdd: sdd1 sdd2 sdd3 sdd4 < sdd5 >
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 0,  type 0
modprobe: Can't locate module ohci-hcd
modprobe: Can't locate module uhci-hcd
ehci_hcd 0000:00:05.2: Philips Semiconductors USB 2.0 Host Controller
ehci_hcd 0000:00:05.2: irq 30, pci mem 0x80043000
ehci_hcd 0000:00:05.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:05.2: USB 2.0 initialized, EHCI 0.95, driver 26 Oct 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
loop: loaded (max 8 devices)
modprobe: Can't locate module redboot
physmap flash device: 8000000 at f0000000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
  Feature/Command Support:      00CE
     - Chip Erase:              unsupported
     - Suspend Erase:           supported
     - Suspend Program:         supported
     - Legacy Lock/Unlock:      supported
     - Queued Erase:            unsupported
     - Instant block lock:      unsupported
     - Protection Bits:         supported
     - Page-mode read:          supported
     - Synchronous read:        unsupported
     - Simultaneous operations: unsupported
  Supported functions after Suspend: 01
     - Program after Erase Suspend: supported
  Block Status Register Mask: 0001
     - Lock Bit Active:      yes
     - Valid Bit Active:     no
  Vcc Logic Supply Optimum Program/Erase Voltage: 3.3 V
cfi_cmdset_0001: Erase suspend on write enabled
cmdlinepart partition parsing not available
RedBoot partition parsing not available
modprobe: Can't locate module usbnet
XScale specific procedures have been done.
Creating node for sda3 
Creating node for sda4 
Creating node for sda5 
Creating node for sdb 
Creating node for sdb1 
Creating node for sdb2 
Creating node for sdb3 
Creating node for sdb4 
Creating node for sdb5 
Creating node for sdc 
Creating node for sdc1 
Creating node for sdc2 
Creating node for sdc3 
Creating node for sdc4 
Creating node for sdc5 
Creating node for sdd 
Creating node for sdd1 
Creating node for sdd2 
Creating node for sdd3 
Creating node for sdd4 
Creating node for sdd5 
Creating node for mtdblock0 
Check sda for sysid
get sysid from sda: 4410493e.81991193,4410493e.81993e0d,4410493e.8199611b,4410493e.81996270
Check sda
Check sdb
Check sdc
Check sdd
cat: /tmp/new: No such file or directory
cat: /tmp/old: No such file or directory
Old drives: 
New drives: 
No new or old disks
/sbin/restore: line 589:   971 Terminated              cat /dev/pic >/tmp/pic
Not restoring...
Activating EVMS ...
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bind<dm-0>
md: bind<dm-1>
md: bind<dm-2>
md: bind<dm-3>
raid5: measuring checksumming speed
   arm4regs  :   383.600 MB/sec
   8regs     :   428.400 MB/sec
   32regs    :   470.000 MB/sec
raid5: using function: 32regs (470.000 MB/sec)
md: raid5 personality registered as nr 4
raid5: device dm-3 operational as raid disk 3
raid5: device dm-2 operational as raid disk 2
raid5: device dm-1 operational as raid disk 1
raid5: device dm-0 operational as raid disk 0
raid5: allocated 4194kB for md3
raid5: raid level 5 set md3 active with 4 out of 4 devices, algorithm 0
RAID5 conf printout:
 --- rd:4 wd:4 fd:0
 disk 0, o:1, dev:dm-0
 disk 1, o:1, dev:dm-1
 disk 2, o:1, dev:dm-2
 disk 3, o:1, dev:dm-3
md: bind<dm-5>
md: bind<dm-6>
md: bind<dm-7>
md: bind<dm-8>
md: raid1 personality registered as nr 3
raid1: raid set md2 active with 4 out of 4 mirrors
md: bind<dm-10>
md: bind<dm-11>
md: bind<dm-12>
md: bind<dm-13>
raid1: raid set md0 active with 4 out of 4 mirrors
md: bind<dm-15>
md: bind<dm-16>
md: bind<dm-17>
md: bind<dm-18>
raid1: raid set md1 active with 4 out of 4 mirrors

EVMS Command Line Interpreter Version 2.5.3


Volume Name: /dev/evms/Volume1
Major: 254
Minor: 4
Active: TRUE
Volume Size: 696.05 GB
Minor Number: 4
This volume is not mounted.
Filesystem: XFS
Max Filesystem Size: 0.00 bytes
Min Filesystem Size: 696.05 GB

Volume Name: /dev/evms/log
Major: 254
Minor: 9
Active: TRUE
Volume Size: 125.44 MB
Minor Number: 9
This volume is not mounted.
Filesystem: XFS
Max Filesystem Size: 0.00 bytes
Min Filesystem Size: 112.00 MB

Volume Name: /dev/evms/root
Major: 254
Minor: 14
Active: TRUE
Volume Size: 509.75 MB
Minor Number: 14
This volume is not mounted.
Filesystem: XFS
Max Filesystem Size: 0.00 bytes
Min Filesystem Size: 509.72 MB

Volume Name: /dev/evms/swap
Major: 254
Minor: 19
Active: TRUE
Volume Size: 250.94 MB
Minor Number: 19
This volume is not mounted.
Filesystem: SWAPFS
Max Filesystem Size: 16.00 PB
Min Filesystem Size: 20.00 MB

mknod: `/dev/md0': File exists
md_operate
registered disk: md0, (9:0)
md_operate exited-0
Performing operate ioctl
0
md_operate
registered disk: md0, (9:0)
md_operate exited-0
Performing operate ioctl
0
mknod: `/dev/md1': File exists
md_operate
registered disk: md1, (9:1)
md_operate exited-0
Performing operate ioctl
0
md_operate
registered disk: md1, (9:1)
md_operate exited-0
Performing operate ioctl
0
mknod: `/dev/md2': File exists
md_operate
registered disk: md2, (9:2)
md_operate exited-0
Performing operate ioctl
0
md_operate
registered disk: md2, (9:2)
md_operate exited-0
Performing operate ioctl
0
mknod: `/dev/md3': File exists
md_operate
registered disk: md3, (9:3)
md_operate exited-0
Performing operate ioctl
0
md_operate
registered disk: md3, (9:3)
md_operate exited-0
Performing operate ioctl
0
flush superblock on disks
md3
md2
md1
md0
Performing debug ioctl
0

EVMS Command Line Interpreter Version 2.5.3


Logical Disk Name: sda
Major: 8
Minor: 0
Active: TRUE
Logical Disk Size: 232.89 GB
Logical Disk Geometry: 30401 Cylinders, 255 Heads, 63 Sectors per Track, 512
Bytes per Sector
LBA of the 1024 Cylinder Limit: 16434495

Logical Disk Name: sdb
Major: 8
Minor: 16
Active: TRUE
Logical Disk Size: 232.89 GB
Logical Disk Geometry: 30401 Cylinders, 255 Heads, 63 Sectors per Track, 512
Bytes per Sector
LBA of the 1024 Cylinder Limit: 16434495

Logical Disk Name: sdc
Major: 8
Minor: 32
Active: TRUE
Logical Disk Size: 232.89 GB
Logical Disk Geometry: 30401 Cylinders, 255 Heads, 63 Sectors per Track, 512
Bytes per Sector
LBA of the 1024 Cylinder Limit: 16434495

Logical Disk Name: sdd
Major: 8
Minor: 48
Active: TRUE
Logical Disk Size: 232.89 GB
Logical Disk Geometry: 30401 Cylinders, 255 Heads, 63 Sectors per Track, 512
Bytes per Sector
LBA of the 1024 Cylinder Limit: 16434495


EVMS Command Line Interpreter Version 2.5.3


Volume Name: /dev/evms/Volume1
Major: 254
Minor: 4
Active: TRUE
Volume Size: 696.05 GB
Minor Number: 4
This volume is not mounted.
Filesystem: XFS
Max Filesystem Size: 0.00 bytes
Min Filesystem Size: 696.05 GB

Volume Name: /dev/evms/log
Major: 254
Minor: 9
Active: TRUE
Volume Size: 125.44 MB
Minor Number: 9
This volume is not mounted.
Filesystem: XFS
Max Filesystem Size: 0.00 bytes
Min Filesystem Size: 112.00 MB

Volume Name: /dev/evms/root
Major: 254
Minor: 14
Active: TRUE
Volume Size: 509.75 MB
Minor Number: 14
This volume is not mounted.
Filesystem: XFS
Max Filesystem Size: 0.00 bytes
Min Filesystem Size: 509.72 MB

Volume Name: /dev/evms/swap
Major: 254
Minor: 19
Active: TRUE
Volume Size: 250.94 MB
Minor Number: 19
This volume is not mounted.
Filesystem: SWAPFS
Max Filesystem Size: 16.00 PB
Min Filesystem Size: 20.00 MB


EVMS Command Line Interpreter Version 2.5.3


Region Name: md/md0
Major: 9
Minor: 0
Active: TRUE
Region Size: 509.75 MB
Region Type: Data

XFS mounting filesystem dm-14
Root device will be: /dev/evms/root
Preparations completed, loading system ...
XFS mounting filesystem dm-14
VFS: Mounted root (xfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing init memory: 92K

INIT: version 2.85 booting

Welcome to ApplianceWare
Press 'I' to enter interactive startup
Mounting proc filesystem [ DONE ]

Setting hostname HOST3D14835F.localdomain: [ DONE ]

Checking root filesystem
[/sbin/fsck.xfs (1) -- /] fsck.xfs -ay /dev/evms/root 
[ DONE ]

Remounting root filesystem in read/write mode: [ DONE ]

Setting system clock (localtime): [ DONE ]

Today's date: Thu Jun 15 02:43:29 CEST 2006 [ DONE ]

Finding module dependencies: [ DONE ]

Configuring kernel parameters: [ DONE ]

Loading module sanmina_7seg_leds: [ DONE ]

Activating EVMS: [ DONE ]

Checking filesystems
Checking all file systems.
[ DONE ]

Mounting local filesystems: [ DONE ]

Checking loopback filesystems: Checking all file systems.
[ DONE ]

Mounting loopback filesystems: [ DONE ]

Turning on user and group quotas for local filesystems: [ DONE ]

Cleaning up temporary files from previous boot: [ DONE ]
Enabling swap space: [ DONE ]
Updating chrooted environments: [ DONE ]

INIT: Entering runlevel: 3

Entering non-interactive startup
Starting hotplug: [ DONE ]

Preparing dev filesystem:[ DONE ]

[ DONE ]

Starting udevd: [ DONE ]

Starting nicdetect_lena: [ DONE ]

USB Interface not found: [ DONE ]

Starting logchecker daemon...
Starting fix_volumesd: [ DONE ]

Configuring kernel parameters: [ DONE ]

Bringing up interface lo: [ DONE ]

Bringing up interface eth0: [ DONE ]

Bringing up interface eth1: [ DONE ]

Starting serviceware: [ DONE ]

Starting mdadm service: [ DONE ]

Initializing random number generator: [ DONE ]

Mounting other filesystems (if any): [ DONE ]

Starting system logger service: [ DONE ]

Starting kernel logger service: [ DONE ]

Starting crond service: [ DONE ]

Starting ftpmount service: [ DONE ]

Starting xinetd service: [ DONE ]

Starting sshd service: [ DONE ]

Starting rawdevices: [ DONE ]

Starting PIC Daemon: [ DONE ]


Starting CIFS services:  NetBIOS over TCP/IP server, Samba server[ DONE ]

Starting Winbind services: [ DONE ]

Value 0x00 written, readback matched
Value 0x03 written, readback matched
Value 0x2a written, readback matched
Value 0x2a written, readback matched
Value 0xe0 written, readback matched
Value 0xe1 written, readback matched
INIT: cannot execute "/sbin/update"

Welcome to ApplianceWare / ttyS0
HOST3D14835F.localdomain login:

DMESG

The following tekst is copied from /var/log/dmesg:

[root@HOST3D14835F drives]# cat /var/log/dmesg
Linux version 2.6.10-sanmina-aw22 (sandman@alconost.sam-solutions.net) (gcc version 3.4.3 20050104 (ALT Linu
x, build 3.4.3-alt2)) #1 Wed Dec 14 18:10:39 MSK 2005
CPU: XScale-IOP8032x Family [69052e30] revision 0 (ARMv5TE)
CPU: D VIVT undefined 5 cache
CPU: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Machine: Sanmina
Memory policy: ECC enabled, Data cache writealloc
On node 0 totalpages: 65536
  DMA zone: 65536 pages, LIFO batch:16
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: satadriver=sata_vsc fstype=xfs  console=ttyS0,115200 cachepolicy=writealloc ecc=on init
rd=0xa2000000,8M
PID hash table entries: 2048 (order: 11, 32768 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB = 256MB total
Memory: 248192KB available (2469K code, 595K data, 92K init)
Calibrating delay loop... 593.10 BogoMIPS (lpj=2965504)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 8192K
NET: Registered protocol family 16
machine_arch_type: 327
PCI init
maÓhine similar to iq31244
PCI: bus0: Fast back to back transfers disabled
pci_dev->irq: 0 pci_dev->pretty_name: Intel Corp. 82541EI Gigabit Ethernet Controller idsel: 1 pin: 1
pci_dev->irq: 14 pci_dev->pretty_name: Intel Corp. GD31244 PCI-X SATA HBA idsel: 3 pin: 1
pci_dev->irq: 0 pci_dev->pretty_name: Intel Corp. 82541EI Gigabit Ethernet Controller (#2) idsel: 4 pin: 1
pci_dev->irq: 0 pci_dev->pretty_name: Philips Semiconductors USB 1.1 Host Controller idsel: 5 pin: 1
pci_dev->irq: 0 pci_dev->pretty_name: Philips Semiconductors USB 1.1 Host Controller (#2) idsel: 5 pin: 1
pci_dev->irq: 0 pci_dev->pretty_name: Philips Semiconductors USB 2.0 Host Controller idsel: 5 pin: 1
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Enable CCNT succ
Intel IOP3XX DMA Copyright(c) 2004 Intel Corporation
NetWinder Floating Point Emulator V0.97 (double precision)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with ACLs, security attributes, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
I2C: M41ST85W RTC driver successfully loaded
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0xfe800000 (irq = 30) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
Intel(R) PRO/1000 Network Driver - version 5.5.4-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
netconsole: not configured, aborting
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd 0000:00:05.0: Philips Semiconductors USB 1.1 Host Controller
ohci_hcd 0000:00:05.0: irq 30, pci mem 0x80041000
ohci_hcd 0000:00:05.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd 0000:00:05.1: Philips Semiconductors USB 1.1 Host Controller (#2)
ohci_hcd 0000:00:05.1: irq 30, pci mem 0x80042000
ohci_hcd 0000:00:05.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
I2C transfer error
I2C transfer error
Querying interrupt mode from PIC unsuccessful.  Returned 0
Defaulting to Polled Mode
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
EXT2-fs warning: checktime reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
libata version 1.10 loaded.
sata_vsc version 1.0
ata1: SATA max UDMA/133 cmd 0xD086A200 ctl 0xD086A229 bmdma 0xD086A270 irq 27
ata2: SATA max UDMA/133 cmd 0xD086A400 ctl 0xD086A429 bmdma 0xD086A470 irq 27
ata3: SATA max UDMA/133 cmd 0xD086A600 ctl 0xD086A629 bmdma 0xD086A670 irq 27
ata4: SATA max UDMA/133 cmd 0xD086A800 ctl 0xD086A829 bmdma 0xD086A870 irq 27
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
ata1: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48

Hotplug event!
Hotplug event on port:0
ata1: dev 0 configured for UDMA/133
scsi0 : sata_vsc
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
ata2: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48

Hotplug event!
Hotplug event on port:1
ata2: dev 0 configured for UDMA/133
scsi1 : sata_vsc
ata3: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
ata3: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48

Hotplug event!
Hotplug event on port:2
ata3: dev 0 configured for UDMA/133
scsi2 : sata_vsc
ata4: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f
ata4: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48

Hotplug event!
Hotplug event on port:3
ata4: dev 0 configured for UDMA/133
scsi3 : sata_vsc
elevator: using anticipatory as default io scheduler
  Vendor: ATA       Model: ST3250824AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
  Vendor: ATA       Model: ST3250824AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 >
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0,  type 0
  Vendor: ATA       Model: ST3250824AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdc: drive cache: write back
 sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 >
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi2, channel 0, id 0, lun 0,  type 0
  Vendor: ATA       Model: ST3250824AS       Rev: 3.AA
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdd: drive cache: write back
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdd: drive cache: write back
 sdd: sdd1 sdd2 sdd3 sdd4 < sdd5 >
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg3 at scsi3, channel 0, id 0, lun 0,  type 0
ehci_hcd 0000:00:05.2: Philips Semiconductors USB 2.0 Host Controller
ehci_hcd 0000:00:05.2: irq 30, pci mem 0x80043000
ehci_hcd 0000:00:05.2: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:05.2: USB 2.0 initialized, EHCI 0.95, driver 26 Oct 2004
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
loop: loaded (max 8 devices)
physmap flash device: 8000000 at f0000000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank
phys_mapped_flash: Found an alias at 0x1000000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x2000000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x3000000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x4000000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x5000000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x6000000 for the chip at 0x0
phys_mapped_flash: Found an alias at 0x7000000 for the chip at 0x0
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
  Feature/Command Support:      00CE
     - Chip Erase:              unsupported
     - Suspend Erase:           supported
     - Suspend Program:         supported
     - Legacy Lock/Unlock:      supported
     - Queued Erase:            unsupported
     - Instant block lock:      unsupported
     - Protection Bits:         supported
     - Page-mode read:          supported
     - Synchronous read:        unsupported
     - Simultaneous operations: unsupported
  Supported functions after Suspend: 01
     - Program after Erase Suspend: supported
  Block Status Register Mask: 0001
     - Lock Bit Active:      yes
     - Valid Bit Active:     no
  Vcc Logic Supply Optimum Program/Erase Voltage: 3.3 V
cfi_cmdset_0001: Erase suspend on write enabled
0: offset=0x0,size=0x20000,blocks=128
cmdlinepart partition parsing not available
RedBoot partition parsing not available
device-mapper: 4.3.0-ioctl (2004-09-30) initialised: dm-devel@redhat.com
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bind<dm-0>
md: bind<dm-1>
md: bind<dm-2>
md: bind<dm-3>
raid5: measuring checksumming speed
   arm4regs  :   383.600 MB/sec
   8regs     :   428.400 MB/sec
   32regs    :   470.000 MB/sec
raid5: using function: 32regs (470.000 MB/sec)
md: raid5 personality registered as nr 4
raid5: device dm-3 operational as raid disk 3
raid5: device dm-2 operational as raid disk 2
raid5: device dm-1 operational as raid disk 1
raid5: device dm-0 operational as raid disk 0
raid5: allocated 4194kB for md3
raid5: raid level 5 set md3 active with 4 out of 4 devices, algorithm 0
RAID5 conf printout:
 --- rd:4 wd:4 fd:0
 disk 0, o:1, dev:dm-0
 disk 1, o:1, dev:dm-1
 disk 2, o:1, dev:dm-2
 disk 3, o:1, dev:dm-3
md: bind<dm-5>
md: bind<dm-6>
md: bind<dm-7>
md: bind<dm-8>
md: raid1 personality registered as nr 3
raid1: raid set md2 active with 4 out of 4 mirrors
md: bind<dm-10>
md: bind<dm-11>
md: bind<dm-12>
md: bind<dm-13>
raid1: raid set md0 active with 4 out of 4 mirrors
md: bind<dm-15>
md: bind<dm-16>
md: bind<dm-17>
md: bind<dm-18>
raid1: raid set md1 active with 4 out of 4 mirrors
md_operate
registered disk: md0, (9:0)
md_operate exited-0
md_operate
registered disk: md0, (9:0)
md_operate exited-0
md_operate
registered disk: md1, (9:1)
md_operate exited-0
md_operate
registered disk: md1, (9:1)
md_operate exited-0
md_operate
registered disk: md2, (9:2)
md_operate exited-0
md_operate
registered disk: md2, (9:2)
md_operate exited-0
md_operate
registered disk: md3, (9:3)
md_operate exited-0
md_operate
registered disk: md3, (9:3)
md_operate exited-0
flush superblock on disks
md3
md2
md1
md0
XFS mounting filesystem dm-14
Ending clean XFS mount for filesystem: dm-14
XFS mounting filesystem dm-14
Ending clean XFS mount for filesystem: dm-14
VFS: Mounted root (xfs filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing init memory: 92K
XFS mounting filesystem dm-9
Ending clean XFS mount for filesystem: dm-9
XFS mounting filesystem dm-4
Ending clean XFS mount for filesystem: dm-4
Adding 256948k swap on /dev/evms/swap.  Priority:-1 extents:1

Conclusions:

  • Intel XScale ARMv5TE architecture.
  • 256 MB RAM with ECC.
  • Linux 2.6.10 (built with gcc version 3.4.3).
  • Performs roughly like an Pentium II 300 MHz according to the BogoMIPS calculation, but BogoMIPS don’t count really.
  • XFS filesystem.
 
doc/software/bootlog.txt · Last modified: 2006/06/20 19:57 by admin